- The motors, the pneumatic jacks, and the mandrels are protected by a watertight bulkhead
- The pneumatic mandrels have been tested by thousands of manufactured units
- Mandrels protection by a self-draining, mechanical labyrinthed system (no bellows used)
- The chamfering mandrels and the 1st polishing mandrel are supplied with a mechanical stop
- Conveyor belt speed adjustable by control panel
- The system of transport stability and reduces the breaking of slabs
- Extractable support bar for large pieces
- Motorized pressing bar
- Control panel assembled on adjustable arm, always reachable
- No need of foundations, drainage point
- the narrow strip only to be processed, not the entire slab
- easier way to glue the two pieces together
- almost invisible gluing line
- possibility to create a stock of strips to be used when necessary.
- The motors, the pneumatic jacks, and the mandrels are protected by a watertight bulkhead
- The pneumatic mandrels have been tested by thousands of manufactured units
- Mandrels protection by a self-draining, mechanical labyrinthed system (no bellows used)
- The chamfering mandrels and the 1st polishing mandrel are supplied with a mechanical stop
- Conveyor belt speed adjustable by control panel
- The system of transport stability and reduces the breaking of slabs
- Extractable support bar for large pieces
- Motorized pressing bar
- Control panel assembled on adjustable arm, always reachable
- No need of foundations, drainage point
- Fully automatic straight edge polishing
- Production speeds of 80 to 150 l/f per hour
- No height restrictions for material being processed
- 7 polishing heads enables processing in one pass
- Requires small foot print for set up and operation (Dimensions are 14’x6’)
- The LCH 711 requires no human intervention to oversee the operation and allows the operator to do other jobs
- Cost of lineal feet of finished edge amortized over 5 years is under .30 per foot
- 2 motors allow for V-grooving material for mitered edge
- Number of Polishing Motors: 7
- Number of Beveling Motors: 2
- Total Water Consumption: 12 to 15 gallons/minute
- Total Power Requirement: 230v/3phase/60amps
- Total Dimension of Machine: 10ft x 4ft x 4ft
- Total Weight of Machine: 3,000lbs
- Extension Tables: Standard 3ft in length
- Working Speed: 150 Lineal feet per Hour
- Maximum Abrasive Size: 6″ or 150mm
- Minimum material size: 3 inches x 16 inches (shorter pieces possible like 12″ x 12″ tile, contact us for details)
- Maximum material size: NO MAXIMUM
- Fully automatic straight edge polishing
- Production speeds of 80 to 120 l/f per hour
- No height restrictions for material being processed
- 7 polishing heads enables processing in one pass
- 2 bevellers to assist in perfect shaping of T profile
- 6 radius motors allows for T profile with perfect rounded edges
- The LCH 711 requires no human intervention to oversee the operation and allows the operator to do other jobs
- Number of Polishing Motors: 7
- Number of Beveling Motors: 2
- Number of Radius polishing Motors: 6
- Total Water Consumption: 15 gallons/minute
- Total Power Requirement: 230v/3phase/60amps
- Total Dimension of Machine: 10ft x 4ft x 4ft
- Total Weight of Machine: 3,000lbs
- Extension Tables: Standard 3ft in length
- Working Speed: 150 Lineal feet per Hour
- Maximum Abrasive Size: 6″ or 150mm
- Minimum material size: 3 inches x 16 inches
- Maximum material size: NO MAXIMUM
- 1 CALIBRATING MANDREL to gauge thickness at an adjustable depth (max. 100 mm). The mandrel can be adjusted both laterally and longitudinally with respect to its supporting shaft; moreover, it can be rotated from 0° to 90°, and can also be used to carry out slotting for the drip stone. For Ø 250 mm tools.
- 2 OPPOSING MANDRELS INCLINED AT 45° to cut chamfers and/or bevels of various dimensions. Whenever you need to carry out rounded profile edges, these mandrels, thanks to the use of specific diamond cone trunk grinding wheels greatly help the shaping made by the oscillating mandrels to the desired edge shape. For Ø 130 mm wheels.
- 6 OSCILLATING MANDRELS of which the first two are ready to be equipped with cup-shaped diamond grinding wheels in order to carry out the shaping of the rounded profiles or the grinding of the flat, squared off or inclined profiles. The other four mandrels are equipped with polishing and smoothing abrasive grinding wheels. If necessary all the 6 mandrels can be equipped with abrasive grinding wheels. Other models derived from the standard LTN 621, by adding extra functional units, can be built on request. For Ø 130 mm wheels.
- The control panel is easily accessible on its articulated arm.
- The oscillating mandrels are unified, tested on thousands of machines, and protected by a mazelike mechanical system (without bellows). Each mandrel has a hydraulic motor and makes distinct revolutions.
- The mandrel-holding beam is pressurized and works by a lever-and-rod oscillation system (it requires no maintenance and has been highly tested – 1987 MM original patent) and micro-oscillation for flat parts.
- The oscillation system is driven by two motors connected and ruled by a single inverter, which allows mechanical simplification, reduced maintenance, high performance, and good reliability.
- The color, tactile programmer (touchscreen) allows to set the machine quickly and intuitively by choosing various default profiles.
- The positioning of the first self-shaping mandrel is automatic.
- The default programming can be customized and stored.
- It is possible to carry out partial processing and to program distinct advances and delays for the engagement of each pneumatic mandrel.
- The programmer has also the following functions:
- DIAGNOSTICS: to find out any working anomalies and/or failures;
- WORKING STATISTICS: to store quantities according to the types of processing performed (partial, resetting and total counters);
- MAINTENANCE SCHEDULE: it reminds the user the ordinary maintenance to be carried out.
- 1 EDGE-MILLING MANDREL to carry out a precisely measured and squared milling of the edge. This passage guarantees maximum accuracy for chamfers and pencil-round corners.
- Dimensions: from 4950×1860 mm onwards
- Power: from 34 kW onwards
- no. 1 CALIBRATION MANDREL to gauge thickness at an adjustable depth (max. 60 mm). The mandrel can be adjusted both laterally and longitudinally with respect to its supporting shaft; moreover, it can be rotated from 0° to 90°, and can also be used to carry out embeddings for the drip stone; for Ø 250 mm tools.
- no. 2 OPPOSING MANDRELS INCLINED AT 45° to order chamfers and/or beveling of various dimensions. Whenever you need to carry out rounded profile edges, these mandrels, thanks to the use of specific diamond cone-trunk grinding wheels greatly helped the following shaping made by the oscillating mandrels by carrying out the milling of the edge; for Ø 130 mm wheels.
- no. 8 OSCILLATING MANDRELS of which the first two are ready to be equipped with cup-shaped diamond grinding wheels to carry out the shaping of the rounded profiles or the grinding of the flat, squared off or inclined profiles. The other five mandrels are equipped with polishing and smoothing abrasive grinding wheels. If necessary, all the 7 mandrels can be equipped with abrasive grinding wheels; for Ø 150 mm wheels.
- Shaping of rounded edges carried out without using of shaped diamond wheels
- Electronic starting and working of the pneumatic mandrels (programming the process beginning and end; programming separate advances and delays for each mandrel)
- Automatic positioning for the first 2 self-shaping mandrels
- Mandrels protection by a self-draining, mechanical labyrinth system (no bellows used)
- Hydraulic oscillating mandrel motors
- Oscillation system by two motors connected by an electrical axle, with high oscillation frequencies, which allows a mechanical simplification, a reduced maintenance, and a reliable high performance.
- Unified oscillating mandrels, each one with a hydraulic motor with differentiated rounds.
- Pressurized mandrel-holding beam with lever-and-rod oscillation (no maintenance and well-tried system – 1987 MM patent).
- Micro oscillation for flat parts.
- Roller system to process narrow strips of material.
- The pneumatic mandrels have been tested by thousands of manufactured units
- The system of transport guarantees a very good stability and reduces the breaking of slabs
- Motorized pressing bar
- Conveyor belt speed adjustable by control panel
- Control panel assembled on adjustable arm, always reachable
- Extractable supporting bar for large pieces
After the success of the last V/O version of the LCV edge polisher, Marmo Meccanica is now proposing the same machine in the horizontal version, that is the LCH M-O/V.
In alternative to the “V-GROOVING” system, the new “V/O-CUTTING” system allows to polish on a continuous mode minimum 45 mm wide and maximum 30 mm thick back splashes and produce narrow strips with the same dimensions ready to be glued on “L” bordered kitchen tops.
The LCH M-O/V is a simple and affordable machine that, beyond being equipped with the “V/O-CUTTING” system, maintains all the features of an edge polisher for up to 60 mm thick slabs, chamfers, calibration and drip-cut.
Two machines in one! The LCH-711M-SU is equipped with an outgoing motor that can be used for either 45 degree miter cutting or tooled with a profiling wheel.
If you are looking to process narrow strips, we offer a machine with a shortened bench that can polish and miter 1 3/4 “ pieces without the option to profile.
IN STOCK!
The LCH 711 machine is the horizontal standard for the flat polishing machines in the industry. This machine is capable of polishing straight flat-squared 1 to 6 cm thick marble, granite, or engineered stone edges at over 120 lineal feet per hour. The working mode is on a continuous process basis; this means that all the pieces are loaded one after the other on the machine and move past a series of polishing motors so that they come out completely finished including a micro-bevel on the top and bottom of the material. The LCH produces material vertically, as they are usually handled, and it is this system that, besides avoided possible breaks of the material, reduces machine cluttering in your warehouse and also the area necessary for the operation. Moreover, the LCH does not require either foundations or treatment for water discharge. In fact, it can be simply placed on the ground and as it is completely streamlined, the discharged water can be easily directed to a point at some distance, by means of a hose connected to a special drain.
LCR is a special, line polisher for flat edges. Indeed, compared to other machines of the same kind, it can round and polish the two corners of a flat edge, besides chamfering them at 45° as all other machines can normally do. Flat edge at 90° with the rounding of the two corners is a kind of processing more and more required, especially in certain markets. So far just torus polishers, both with belt and stationary bench, have carried out this kind of processing. However, those machines are rather slow as for this kind of profile (much slower compared than flat edge with chamfering or completely rounded edges). On the contrary LCR can perform the above profile as fast as polishing machines for flat edge can do, and better than torus polishers, even on “difficult” materials, such as agglomerates. Besides the facing-polishing mandrels, LCR is also supplied with two units of three counter-oscillating mandrels each, that carry out travels of about 90° through an original and innovative mechanism planned by MM. That mechanism generates a natural, harmonious motion. It makes the masses of the two oscillating units balance out each other (and the reversing stresses compensate), thus allowing high oscillating frequencies. Alternatively, the two units of mandrels can be used in a static way (opposed at 45°), thus performing “classic” chamfering. LCR can be supplied with all the attachments available for other edge-polishing machines.
IN STOCK!
LTN is a polishing machine for round edges up to 8 cm and flat edges up to 10 cm thickness, born by the need to create an essential, solid and compact machine at an affordable price that is equipped with a high level of automation. The LTN maintains the shaping principle by means of a single cup-shaped diamond wheel for all profiles and thicknesses. The oscillation system is driven by two motors connected and ruled by a single inverter, which allows mechanical simplification, reduced maintenance, high performance and good reliability. The structure is monocoque and self-supporting (not coated and tubular framed). Waste water is piped in a unique collector (it neither falls directly to the ground nor on the bearing base of the machine). All protections are made of strong and safe stainless steel.
a wide range of supplementary automations and accessories available
Dimensions from 4000 x 1900 mm
Power: from 26 Kw
IN STOCK!
LTX COMBI, like all the Marmo Meccanica machines, stands out for the quality of the work, its sturdiness, the safety standards adopted, which guarantee maximum protection for the operator, and the practical and accessible technical solutions.
The LTX COMBI project has been designed to condense all flat, rounded, round-flat polishing on rectilinear edges in a single machine equipped with two sets of spindles: one specific for rounded edges (derived from LTN) and the other for flat ones (derived from LCH). For this reason, with LTX COMBI it is possible not only to process both round and flat profiles, but in particular the production of profiles with both round and flat surfaces, such as demi-bullnose or pencil rounds, will considerably speed up.
Equipment:
LTX COMBI standard is equipped with:
No. 1 ADJUSTABLE ENTRY BAR, from 0 to 6 mm, to register highly accurate measurements for the edge-milling mandrel.
No. 1 INGOING CALIBRATING/DRIP CUTTING UNIT to gauge thickness at an adjustable depth (max. 100 mm). The mandrel can be adjusted both laterally and longitudinally on its supporting shaft; plus, it can be rotated 0°-90°, and can also be used to carry out slotting for the drip stone. For Ø 250 mm tools.
No. 2 OPPOSING MANDRELS INCLINED AT 45° to cut chamfers and/or bevels of various dimensions. Whenever you need to carry out rounded profile edges, these mandrels, if equipped with specific diamond cone trunk grinding wheels, greatly help the shaping made by the oscillating mandrels to the desired edge shape. For Ø 130 mm wheels.
No. 6 OSCILLATING MANDRELS to carry out the shaping of rounded and inclined profiles. The first one can be equipped with cup-shaped diamond grinding wheels in order. The other five mandrels are equipped with polishing and smoothing abrasive grinding wheels. If necessary, all 6 mandrels can be equipped with abrasive grinding wheels. For Ø 130 mm wheels.
No. 5 STILL POLISHING/FACING MANDRELS to carry out the processing of all flat and flat-round profiles. The first one has an adjustable mechanical limit switch and can be equipped with diamond grinding wheels. For Ø 130 mm wheels.
No. 2 OPPOSING MANDRELS INCLINED AT 45° to polish chamfers. For wheels up to Ø 130 mm.
Main Features:
The oscillating mandrels are unified, tested on thousands of machines, and protected by a mazelike mechanical system (without bellows). Each mandrel has a hydraulic motor and makes distinct revolutions.
The mandrel-holding beam is pressurized and works by a lever-and-rod oscillation system (it requires no maintenance and has been highly tested over the years – 1987 Marmo Meccanica original patent) and micro-oscillation for flat parts.
The oscillation system is driven by two motors connected through an electric axle, which allows mechanical simplification, reduced maintenance, high performance, and good reliability.
The positioning of the functional units is automatic.
The PLC software-controlled functioning of the units allows partial processing, as well as advance and delay programming for each pneumatically actioned mandrel.
Conveyor belt speed adjustable by control panel.
The system of transport guarantees a very good stability and reduces the breaking of slabs.
Extractable supporting bar for large pieces (up to 27 inches from the belt)
Water drainage system: no water on the ground, no foundations needed for the installation.
The control panel is easily accessible on its articulated arm.
The touchscreen programmer allows to set the machine quickly and intuitively by choosing among various default profiles. The default programs can be customized and stored.
It is possible to carry out partial processing and to program distinct advances and delays for the engagement of each pneumatic mandrel.
The programmer has also the following functions:
DIAGNOSTICS: to find out any working anomalies and/or failures;
WORKING STATISTICS: to store quantities according to the types of processing performed (partial, resetting and total counters);
MAINTENANCE SCHEDULE: it reminds the user the ordinary maintenance to be carried out.
IN STOCK!
High performance and reliability are the main features of these torus-polishing machines. Round edges are shaped by 2 cup-shaped diamond wheels (150 mm diameter) whose positioning is completely automatic. – Micro oscillation system for flat edges and/or portions of flat edges. – Electronic control of the pneumatic mandrels (possibility of setting the beginning and the end of a processing, and the individual advances and delays) with TOUCH SCREEN control panel. – Right for high output (at the height of its grade), for the processing of thicknesses beyond 6 cm (up to 10 cm), and for the processing of soft materials thanks to the good sliding sensitivity of the polishing mandrels.
Models and accessories:
This machine is proposed in 2 basic versions: LTZ 821 and LTZ 8221.
The LTZ 8221 is identical but equipped with no. 2 outgoing CHAMFERING MANDRELS.
Several accessories and supplementary groups are available on request.